Neo Paints

How To Paint FLOORS

IMPORTANT THINGS TO KNOW WHEN PAINTING

  • Always follow the instructions on the product label for best results.
  • Preparation and correct product application are important.
  • There are no short-cuts.
  • Always follow the correct drying time recommendations.
  • Keep the room well ventilated when using an oil-based/solvent based paint.
  • Do not paint exterior surfaces when rain is expected within 4 hours after paint application.
  • Do not paint if surface temperatures are below 10 or above 30°C
  • Do not paint exterior surfaces in windy conditions.
Download Instructions

New Floors

Concrete Floors - Interior Paint

  1. Make sure the floor is dry and free of any contamination for e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  2. Sweep floor twice with soft broom and mop with a damp mop (do not wet floor or use dripping wet mop).
  3. Let surface dry for 2 hours.
  4. Apply one coat of “NEO Floor Paint” diluted with 5 to 10% of “NEO Mineral Turpentine” and allow to dry for 24 hours.
  5. Apply another coat of  “NEO Floor Paint” undiluted and allow to dry for 24 hours.
    NOTE: Apply the paint with a quality brush or Mohair Rolle. Use “NEO Mineral Turpentine” as cleaning solvent.
  1. Make sure the floor is dry and free of any contamination for e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  2. Sweep floor twice with soft broom and mop with a damp mop (do not wet floor or use dripping wet mop).
  3. Let surface dry for 2 hours.
  4. Apply one coat of “NEO Epoxy Floor Paint” diluted with 10% of  “NEO Epoxy Thinner” and allow to dry for 24 hours.
  5. Apply another coat “NEO Epoxy Floor Paint” undiluted and allow to dry for 24 hours.
    NOTE: Apply with a quality brush or Mohair Roller.  Use  “NEO Epoxy Thinner” as cleaning solvent

Concrete Floors (Interior - Stone Sealer)

  1. Make sure the floor is dry and free of any contamination for e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  2. Sweep floor twice with soft broom and mop with damp mop (do not wet floor or use dripping wet mop).
  3. Let dry for 2 hours.
  4. Apply two to three coats of  “NEO Stone Sealer (water based)” allowing 8 hours drying time between coats.
  5. Allow to dry for 24 hours after final coat.
    NOTE: Apply with a quality brush or Sheepskin Roller. Use water as cleaning solvent.
  1. Make sure the floor is dry and free of any contamination e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  2. Sweep the floor twice with a soft broom and mop with a damp mop (do not wet the floor or use a dripping wet mop).
  3. Let dry for 2 hours. Apply two to three coats of “NEO Stone Sealer (Solvent-based)”, allowing 8 hours drying time between coats.
  4. Allow to dry for 24 hours after the final coat.
    NOTE: Apply with a brush or Mohair Roller. Use  ‘NEO M-Thinner” as a cleaning solvent.

Exterior Paint

  1. Only suited for floors which have proper damp proofing installed underneath the floor!
  2. Make sure the floor is dry and free of any contamination e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  3. Sweep the floor twice wa ith soft broom and mop with a damp mop (do not wet the floor or use a dripping wet mop).
  4. Let dry for 2 hours. Apply one coat of  “NEO Floor Paint” diluted with 5 to 10% “NEO Mineral Turpentine” and allow to dry for 24 hours.
  5. Apply another coat of “NEO Floor Paint” undiluted and allow to dry for 24 hours.
    NOTE: Apply with a quality brush or Mohair Roller.  Use “NEO Mineral Turpentine” as cleaning solvent
  1. Make sure the floor is dry and free of any contamination for e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  2. Sweep the floor twice with a soft broom and mop with a damp mop (do not wet the floor or use a dripping wet mop).
  3. Let dry for 2 hours. Apply one coat of “NEO Salt Stop” and allow to dry for 24 hours.
  4. Apply two to three coats of “NEO Tennis Court Paint”, allowing 4 hours drying time between coats.
  5. Allow to dry for 24 hours after the final coat.
    NOTE: Apply with a quality brush or Sheepskin Roller. Use water as a cleaning solvent.

Exterior - Stone Sealer

  1. Make sure the floor is dry and free of any contamination e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  2. Sweep the floor twice with a soft broom and mop with a damp mop (do not wet the floor or use a dripping wet mop).
  3. Let dry for 2 hours.
  4. Apply two to three coats of  “NEO Stone Sealer (water-based)”, allowing 8 hours drying time between coats.
  5. Allow to dry for 24 hours after the final coat.
    NOTE: Apply with a quality brush or Sheepskin Roller. Use water as a cleaning solvent

Wooden Floors (Interior Only)

  1. Sand in the direction of grain to smooth.
  2. Dust properly with damp cloth.
  3. Apply one coat of “NEO Floor Paint” diluted with 10% “NEO Mineral Turpentine” and allow to dry for 24 hours.
  4. Fill surface imperfections with “NEO Repair Paste” and work off to smooth with moist spatula. Larger imperfections should be filled in 2 mm thick layers and each layer  allowed to dry for 2 hours before the next layer).
  5. Allow to dry for 24 hours.
  6. Apply one undiluted coat of “NEO Floor Paint” and allow to dry 24 hours.
    NOTE: Apply with a quality brush or Mohair Roller. Use “NEO Mineral Turpentine” as cleaning solvent
  1. Sand in the direction of the grain to smooth.
  2. Dust properly with a damp cloth.
  3. Apply one coat of “NEO Siegellack” diluted with 10% “NEO Mineral Turpentine” and allow to dry for 24 hours.
  4. Sand slightly and dust properly.
  5. Apply one to two undiluted coats of “NEO Siegellack” and allow to dry for 24 hours (Sand and dust between coats).
    NOTE: Apply with a quality brush or Mohair Roller. Use ‘NEO Mineral Turpentine” as a cleaning solvent.

Renovated Floors

Concrete Floors - Interior Paint

  1. Make sure the floor is dry and free of any contamination for e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  2. Remove any flaking and blistering paint mechanically & make sure existing coating is compatible with “NEO Floor Paint”.
  3. Sweep floor twice with soft broom and mop with damp mop (do not wet floor or use dripping wet mop).
  4. Let dry for 2 hours.
  5. Spot prime exposed cement with “NEO Floor Paint” diluted with 5 to 10% “NEO Mineral Turpentine” and allow to dry for 24 hours.
  6. Apply another coat “NEO Floor Paint” undiluted over whole surface and allow to dry for 24 hours.
    NOTE: Apply with a quality brush or Mohair Roller. Use “NEO Mineral Turpentine” as cleaning solvent.
  1. Make sure the floor is dry and free of any contamination for e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  2. Remove any flaking and blistering paint mechanically & make sure the existing coating is compatible with “NEO Floor Paint”.
  3. Sand existing epoxy coating to mat, sweep floor twice with soft broom and mop with damp mop (do not wet floor or use dripping wet mop).
  4. Let dry for 2 hours. Spot prime bare cement with “NEO Epoxy Floor Paint” diluted with 10% “NEO Epoxy Thinner” and allow to dry for 24 hours.
  5. Apply another coat of “NEO Epoxy Floor Paint” undiluted and allow to dry for 24 hours.
    NOTE: Apply with a quality brush or Mohair Roller. Use “NEO Epoxy Thinner” as a cleaning solvent.

Concrete Floors - Interior Stone Sealer

  1. Make sure the floor is dry and free of any contamination for e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  2. Remove any flaking and blistering existing Sealer mechanically & make sure existing coating is compatible with “NEO Stone Sealer (water based)”.
  3. Sweep floor twice with soft broom and mop with damp mop (do not wet floor or use dripping wet mop).
  4. Let dry for 2 hours. Spot prime bare cement with one coat “NEO Stone Sealer (water based)” and let dry for 8 hours.
  5. Apply two coats “NEO Stone Sealer (water based)” over whole surface allowing 8 hours drying time between coats.
  6. Allow to dry for 24 hours after final coat.
    NOTE: Apply with a quality brush or Sheepskin Roller. Use water as a cleaning solvent.
  1. Make sure the floor is dry and free of any contamination for e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  2. Remove any flaking and blistering existing Sealer mechanically & make sure existing coating is compatible with “NEO Stone Sealer (solvent-based)”.
  3. Sweep the floor twice with a soft broom and mop with a damp mop (do not wet the floor or use a dripping wet mop).
  4. Let dry for 2 hours. Spot prime bare cement with one coat of “NEO Stone Sealer (solvent-based) and let dry for 8 hours.
  5. Apply two coats of “NEO Stone Sealer (solvent-based)” over the whole surface, allowing 8 hours drying time between coats.
  6. Allow to dry for 24 hours after the final coat.
    NOTE: Apply with a quality brush or Mohair Roller. Use “NEO M-Thinner” as a cleaning solvent.

Exterior Paint

  1. Only suitable for floors that have proper damp proofing installed underneath. If existing floor Paint is excessively blistering and peeling, no / damaged damp coring is in place, resulting the paint to fail – such floors cannot be painted.
  2. Make sure the floor is dry and free of any contamination for e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  3. Remove any flaking and blistering paint mechanically & make sure existing coating is compatible with “NEO Floor Paint”.
  4. Sweep floor twice with soft broom and mop with damp mop (do not wet floor or use dripping wet mop).
  5. Let dry for 2 hours. Spot prime bare cement with “NEO Floor Paint” diluted with 5 to 10% “NEO Mineral Turpentine” and allow to dry for 24 hours.
  6. Apply another coat “NEO Floor Paint” undiluted and allow to dry for 24 hours.
    NOTE: Apply with a quality brush or Mohair Roller.  Use “NEO Mineral Turpentine” as cleaning solvent. 
  1. Only suitable for floors that have proper damp proofing installed underneath. If existing floor Paint is excessively blistering and peeling, no / damaged damp coring is in place, resulting the paint to fail – such floors cannot be painted.
  2. Make sure the floor is dry and free of any contamination for e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  3. Remove any blistering and peeling paint and make sure existing coating is compatible with “NEO Tennis Court Paint”.
  4. Sweep floor twice with soft broom and mop with damp mop (do not wet floor or use dripping wet mop).
  5. Let dry for 2 hours. Spot prime bare cement with “NEO Salt Stop” and allow to dry for 24 hours.
  6. Apply two coats “NEO Tennis Court Paint” over whole area allowing 4 hours drying time between coats.
  7. Allow to dry for 24 hours after final coat.
    NOTE: Apply with a quality brush or Sheepskin Roller. Use water as cleaning solvent.

Exterior Stone Sealer

  1. Make sure the floor is dry and free of any contamination for e.g. oil, grease, soap, etc. (get supplier to measure moisture content)
  2. Remove any flaking and blistering existing Sealer mechanically & make sure existing coating is compatible with “NEO Stone Sealer (water based)”.
  3. Sweep floor twice with soft broom and mop with damp mop (do not wet floor or use dripping wet mop).
  4. Spot prime bare cement with one coat “NEO Stone Sealer (water based)” and let dry for 8 hours.
  5. Let dry for 2 hours. Apply two coats “NEO Stone Sealer (water based)” over whole area allowing 8 hours drying time between coats.
  6. Allow to dry for 24 hours after final coat.
    NOTE: Apply with a quality brush or Sheepskin Roller. Use water as a cleaning solvent.

Wooden Floors (Interior Only)

  1. Remove any blistering and flaking paint.
  2. Make sure the existing coating is compatible with “NEO Floor Paint”.
  3. Clean properly with a damp cloth.
  4. Spot prime bare wood with “NEO Floor Paint” diluted with 10% “NEO Mineral Turpentine” and allow to dry for 24 hours.
  5. Fill surface imperfections with “NEO Repair Paste” and work off to smooth with a moist spatula (Larger imperfections should be filled in 2 mm thick layers and each layer allowed to dry for 2 hours before the next layer).
  6. Allow to dry for 24 hours.
  7. Apply one undiluted coat of “NEO Floor Paint” over the whole area and allow to dry for 24 hours.
    NOTE: Apply with a quality brush or Mohair Roller. Use “NEO Mineral Turpentine” as a cleaning solvent.
  1. Sand in the direction of the grain to smooth.
  2. Remove any blistering and flaking paint.
  3. Make sure the existing coating is compatible with “NEO Siegellack”.
  4. Dust properly with a damp cloth. Spot prime bare wood with “NEO Siegellack” diluted with 10% “NEO Mineral Turpentine” and allow to dry for 24 hours.
  5. Sand slightly and dust properly. Apply one to two undiluted coats of “NEO Siegellack” over the whole area and allow to dry 24 hours (Sand and dust between coats).
    NOTE: Apply with a quality brush or Mohair Roller. Use “NEO Mineral Turpentine” as a cleaning solvent.

Made for Namibia

For you. By us.

Made by Namibians

Crafted with pride and skill

Made in Namibia

Locally manufactured

Proudly Namibian

Celebrating our craftsmanship

Scroll to Top